커뮤니티

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Cat flaps let your pet come and go as they please, without you having to let him in or out. They also can help to prevent your cat from toileting in the house.

It is simpler to install the cat flap on a upvc panel than one made of glass, but you will require some expertise and correct tools.

Take a measurement of the door

Fitting a cat door in a front door can be difficult, but as long as the cat flap is the correct one and you follow the instructions you can make it less difficult. We will show you how to draw the shape, using a jigsaw to cut out the area in the door and then finish off the job by securing the flap to the door. This will ensure that the flap stays in place and protects the door from wind and rain causing damage.

The first thing to do is take a measurement of the width of your pet to get a precise measurement of the size of cat flap you will need. This will ensure that the flap is large enough to let your pet leave and enter the home without having to open and close the door each time, yet small enough to stop the pet from straying too far in either direction.

If your kit comes with a drawing showing where to drill then you can place it on the door and then draw a pencil around it. If your door has moulding or sill on the bottom of it then make sure you have enough clearance from these as this will keep your cat safe and stop them from gaining access to your home.

Set a square to check that you're cutting correctly and to ensure the hole is in a rectangle shape. When you are satisfied with this, you are able to begin removing the remaining door material. Utilize a set square to ensure that you are cutting the material in a proper manner and that the cut is a rectangle. When you are satisfied with the result, you can remove the remaining door material.

Draw a Line

The cat flap lets you to let your pet in and out without having to worry about unwanted visitors or unwelcome gifts. It also stops draughts and keeps your home's temperature steady. However, fitting the cat flap to your door might seem like an intimidating task for those who have never done it before, which is why many to hire a professional joiner or carpenter to do the job. This is an option but you can do it yourself if the tools are appropriate and the directions are followed.

This is much simpler to do with a wooden door, but it is possible with replacement upvc door panels with cat flap. However, you must be careful not to damage the doors since this could make it impossible to claim your warranty. First, you need to measure the door to ensure that it can accommodate the new cat-flap. If you have a standard uPVC panel, this should be easy. However when your door is composite or another type of door, you may have to be more cautious.

The next step is to measure the size of your cat's belly. This is the height from the floor to the bottom of the cat's stomach and you will need to find a place on the door that will be within the range your pet can comfortably go through. Once you have this information, you will need to mark out the area with an eraser and a spirit level to be certain that the hole you will make will be a good fit for your cat.

Once you've marked the area, you're now ready to cut the hole. It is crucial to be patient and use a jigsaw to ensure that the cuts are smooth and clean not uneven and rough. This could cause damage to your door. You should also remember to wear safety glasses and a dust protection mask when using the jigsaw, since breathing in the dust could be hazardous to your health. Once you've finished cutting the hole, you'll require sandpaper to smooth the edges so that the cat flap can be easily inserted into the hole.

Cut a Hole

The process of fitting a cat flap glass door installation near me flap to an existing door cat flap in upvc door panel panel or double glazing sealed unit can be quite difficult. It is tempting to do it yourself, but unless have a lot of experience in DIY it is recommended to hire a professional in to do the task for you. A mistake could not only be ugly but also pose an security risk. It could allow cold air in when the cat is outdoors and hot air out when the cat is inside.

The first thing to do is draw the position of the hole in the door with a pencil and a spirit level. This will ensure that it is correctly located and is parallel to other parts of the door. Make sure to have sandpaper on hand to smooth any rough edges.

Wear the safety equipment you'll need to use a power tool. If you're worried about noise, you can get a cordless jigsaw which is quieter and Cat flap in upvc door panel easier.

It is best to only remove the material that is required to fit the cat flap. A little bit of extra material will be needed to cover the thickness of the wall of the flap but removing more than this can cause problems or harm the frame of the door.

A upvc door may contain a metal frame or panel that could interfere with the microchip cat flap, and if this is the case you will need to cut an oversize hole so that the metal does not touch the wall of the cat flap, if this is done it is important to fill in the gap and render it watertight.

If you're looking to install a cat flap into a upvc or double-glazed window with frames made of metal you'll need to talk to a specialist. They will provide you with a brand new piece of glass with the hole that is already designed for the cat flap. This is less expensive than fitting a cat flap inside an existing pane that wasn't designed for this purpose.

Install the Flap

Cat flaps allow your pet to leave and come whenever they want, allowing them the ability to unwind inside the house whenever they're feeling like it. If you have a uPVC front door, it can be hard to install a cat flap. This is especially true when you don't have a glass panel that can be cut. Luckily, if you're happy to buy and install a new half-glazed uPVC panel, it's possible to install an animal flap onto the doors. It's not as simple as simply cutting a hole through wall cat flap the door however, and there are a few things you'll need to do first to make sure it's secure.

A composite, uPVC or GRP door panel is generally composed of a thin plastic skin which is bonded to an insulating polystyrene base. The material is extremely fragile and care must be taken when cutting into it to avoid damaging. This type of door comes with a template that you can use to cut the hole.

After you have marked out the hole in your front door, it's time to install the cat flap. You can buy and fit various models including basic push-button operated ones to microchip activated units that only let in your pet. However, regardless of what type of cat flap in Upvc door panel flap you choose it's crucial to ensure that your cat flaps for french doors can comfortably use the flap without getting stuck outside in the rain.

It's a good idea choose a circular fitting cat flap in upvc door panel rather than one that is square, since circles can be more securely cut into door glass. This is because square holes leave the glass vulnerable to cracking if drilling is applied to it. This is also a safer choice since you don't have to drill into the toughened glass which could break and hurt your pet or your family members. This is especially crucial if you have elderly or children living at home who could be hurt by glass shards.